top of page

Training to Failure: Is It Necessary for Muscle Growth and Strength?

Nov 1
3 min read

Updated: Nov 7


A set ends when the target number of reps is complete, when form begins to break down, or when no further rep is possible. Those are different stopping points, yet training advice often groups them together under one phrase: training to failure.


In resistance training, momentary muscular failure generally means a person cannot complete another repetition through the intended range of motion with proper technique. Some people use “failure” more loosely to mean that a set feels extremely difficult. Being clear about the term matters, because a program that asks for failure on every set is different from one that asks a lifter to stop with a little effort still in reserve.


Is failure required for muscle growth?


The question of lifting to failure for muscle growth is not simply yes or no. Muscle growth can occur when sets are challenging and performed with enough effort, but reaching the point where another rep is impossible is not the only way to make a set productive.


In an eight-week study of resistance-trained adults, participants trained either to momentary failure or stopped with one to two repetitions in reserve. Both approaches produced similar quadriceps growth, while the failure group experienced greater acute neuromuscular fatigue. The study was specific to its participants, exercises and training period, so it does not settle every programming question. It does show that every set does not have to end in a failed rep to support growth. 



And for more scientific information that covers failure training as it relates to athletic development please see here:




What do reps in reserve mean?


Reps in reserve, often shortened to RIR, is an estimate of how many more good-quality repetitions a person could have completed at the end of a set. If a lifter finishes and believes they could have done two more reps, that is approximately two RIR. RIR training uses this estimate to set effort without requiring a failed rep each time.


RIR takes practice. A newer lifter may find it hard to judge whether one, two or four reps were left. The estimate also depends on the exercise, the load and the day. A person’s “two reps left” on a machine exercise may feel different from two reps left during a heavy squat. The goal is not perfect precision; it is to avoid turning every set into an all-out test.


How close to failure should you train?


There is no single number of reps in reserve that fits every exercise and training goal. A lifter might stop a compound movement with a couple of reps left to preserve technique and energy for later sets. On a stable, lower-risk isolation exercise, they may choose to get closer to failure, especially if the target muscle is the main focus.


The question how close to failure to train can be answered by looking at the whole session. If each set goes to failure, repetitions and load may fall sharply as fatigue builds. That can make it harder to maintain good form or complete the planned work. Stopping just short of failure on some sets may allow more consistent performance across the workout.


For strength, repeatedly attempting maximal effort is not always necessary. The reference article provided by the client also discusses using submaximal loads and managing fatigue instead of maxing out frequently. That point can be useful in practice: strength training requires high-quality repetitions and specific practice, not just exhaustion.


What are the risks of failure training?


The main training to failure risks are practical. Fatigue can rise quickly, technique may deteriorate, and the next set or training session may suffer. This matters especially on exercises where a failed rep could be difficult to control or safely exit. Training hard is part of progress; losing control of the movement is not the goal.


This does not mean failure should never be used. It can be a deliberate tool for some exercises, sets or phases of a program. But if every set has to end with a forced rep, the lifter may accumulate fatigue without gaining a clear advantage.


What does the research suggest?


Failure training research compares many different setups: trained and untrained participants, different loads, exercises and definitions of failure. That makes broad claims difficult. A useful reading of the evidence is that challenging sets matter, while the precise need to reach momentary failure depends on the situation. The direct comparison between failure and one-to-two RIR training found similar growth over eight weeks, alongside more fatigue after failure training. 


The better question is not “Should I fail every set?” but “Can I train hard, keep my technique consistent and recover well enough to progress?” For many people, leaving a rep or two in reserve on most sets is a practical starting point. Failure can be used selectively, with control and a reason behind it. That approach keeps effort high without making exhaustion the measure of a successful workout.


Comments


bottom of page